Chapter 88 Week Fifty-Eight January 21, 2008

Posted on by

Jeremy Turner came by the house and helped me make final adjustments to the doors. The fit is good, but not quite as nice as I would prefer. The aluminum wings just don’t fit as well with the doors as the original steel wings, but as my wife, Judith, says, “only you and a concourse judge will see that the fit isn’t perfect!”

Finished Door Assembly 5

Finished Door Assembly 1

LH Door

After finishing up the doors, I put the exhaust clamps on the exhaust system. With the headers and big bore pipes, the exhaust note is a bit louder than the original system, but it sounds great and I can still hear the sound system over the rumble!

The tops and tonneau are the only components that remain. I must say, it feels pretty good to take a look at the Bloody Beast in the driveway. I know it will be even more gratifying to get the Healey out on the road.

Shane and “Little” Shane paid us a visit and, of course, “Little” Shane wanted to inspect the progress on the red car.

Shane & Shane

Little Shane

Chapter 87 Week Fifty-Seven January 14, 2008

Posted on by

The windscreen was a very tight fit! I suppose that it should be to minimize leaks, but it took some tugging on a drift through one of the lower mounting holes in the stanchion and a lot of pushing to finally get the uppermost capscrew to thread into place. The RH side didn’t require any shimming, but the LH did. You do want to make sure that there is no undue force on the stanchions or you might end up with a broken glass! I added a little 3M caulk strip under the post pad seals and between the windscreen frame seal and the post pad. I decided to run the seal under the post pad, though consulting with the “experts” resulted in at least three ways to do this job: under the pad, between the pad and the post, and cut off flush with the pad. I am using post mounted driving mirrors from Cape International, so they were mounted at this time and tightened through the posts.

Windscreen and wipers installed

Capesport Mirrors

After finishing the windscreen, I fixed the original “rainbow” wipers with new rubber to the wiper posts and following the addition of some windscreen washer fluid to the parcel tray mounted fluid reservoirtried out the wipers. All worked fine, including the intermittent wiper rheostatand electric washer pump I has installed previously. The kit from Ed Esslinger also turns on the headlamps when the wipers are activated – a requirement in many states now. 

Next was the installation of the bonnet. I first removed the striker pin assembly so that I could have the bonnet lie flat in the surround. Four 1/4” bolts with the heads to the outside are used to fasten the hinges to the bonnet hinge brackets. This process took some adjusting to get things right and at least one assistant is essential! After getting the bonnet lined up I re-secured the striker pin assembly to the bonnet and adjusted it and the bonnet latch support bracket to align all. The anti-rattle spring was then connected to the hood latch remote control rod and the bonnet release mechanism was tried with success.

Bonnet Latch Assembly

Strike Pin Assembly

Bonnet down

Bonnet Up

 

Chapter 86 Week Fifty-Six January 7, 2008

Posted on by

After a week away from the Healey, I was eager to get back to the final assembly work. Connecting the check strap to each of the doors with the clevis pin was next. I found that making sure the check strap nut was sufficiently tight to hold the door open needed to be done first, then the clevis pin inserted. Both doors stayed open as designed. The RH check strap nut is threaded left handed.

Check Strap Clevis Pin Install

I had pre-drilled the aluminum shut face finishers that were installed following the doors. I discovered that Kilmartin’s are the only ones available that come close to fitting properly. They were sourced from British Car Specialists. The lower sill plate was attached first, followed by the “B” pillar plate. The vertical plate has a piece of vinyl beading glued to the back side to give a finished look to the edge. The aluminum interior door finisher was installed last.

Door Shut Face Finishers 1

Door Shut Face Finishers 2

Door Shut Face Finishers 3

The door striker assembly was then installed and adjusted to line up with the door properly. The assembly consists of the striker, a spacer plate and a drilled back plate. Then the bristleflex door seal from McGregors was installed and the length trimmed to fit properly into the aluminum door seal cap which is screwed into a vinyl covered block of wood.

Furflex Door Seal

With the doors finished, it was time for the installation of the windscreen.

Chapter 84 Week Fifty-Four December 24, 2007

Posted on by

Today (Monday) is Christmas Eve and there is much to be done, so only a little Healey work will happen on this day, but I had a good week. I did manage to install the rubber buffers on the front shroud sill bonnet opening. Three on the left side and two in the right plus the long strip to protect the carbs from the weather. My long strip is cut into two pieces to account for the carb access panel. The buffers are held in place by copper-colored split rivets and flat washersthat are pushed through the mounting hole and then bent over.

LH Rubber Buffers

RH Rubber Buffers 2

LH Carb Panel Seal

The next task was to fit the front wings to the superstructure. I began with the RH wing, thinking it would be the more difficult of the two. First, I tapped the wing clip nuts onto the wings. Three shorter nuts and bolts are used for the front of the wing, below the headlights. With the help of my wife, who held the wing in place, I installed the rearmost and forward most bolts.

With those two holding the wing in position, I then began to install the other bolts working from the front to the rear. Each one was hand tightened enough to get them started, but with enough room to install the wing beading. The fourth nut/bolt from the front requires Houdini to install. I finally accomplished it after loosening each of the four bolts securing the heater blower and then disconnecting the large fresh air hose from the blower. With the hose loose I was able to access the bolt for the fourth hole.

RH Front Wing 1

RH Side with front wing

To protect the paint while installing the beading, I ran a strip of painter’s masking tape on the shroud and the wing parallel to the beading.

Beading Installation

After carefully spreading the beading folding tabs so that they were evenly distributed across the wing, I pressed it in place. Once again, four hands come in handy!

With my wife applying downward pressure on the beading I tightened each bolt/nut until the beading was locked in place and the top of the wing was tight.

Then I tackled the three fasteners below the headlight. These are much easier to access. Again, I loosely attached each of the three and then inserted the two plastic beading pieces between the panels and tightened down.

Next were the three 1/4” x 3/4” long hex head bolts used to secure the bottom edge of the wing. Finally, the 3/8” sheet metal screws were used to fasten the wing flanges to the hinge pillar plate. The heater blower fresh air hose was reinstalled and the blower’s four mounting bolts tightened. A little red touch-up paint on the lower bolts and pillar screw heads and then it was on to the LH wing. NEXT TIME I WOULD WAIT TO FASTEN THE WING AT THE BOTTOM UNITL THE DOOR IS INSTALLED. THERE IS FLEX IN THE WING AND BY MOVING IT UP OR DOWN SLIGHTLY ONE CAN BETTER MATCH UP THE WING CURVATURE WITH THAT OF THE DOOR!

The LH wing was a little easier to install in my case because of the carb access panelI had cut into the shroud! The difficult nuts/bolts on the LH wing were the rearmost two because the wiper motor restricts access to the locating holes and hardware.

It was a good feeling to have all four of the body’s wings in place.

The next task was the installation of the scuttle seals that I had ordered from Bill Bolton. These are reputed to the best available, and the fit does seem to be quite nice. As I was working on the seals and dash pad I had a visit from grandson #2, Shane. As the image shows, he seemed right at home in the Bloody Beast.

Little Shane’s visit to the Garage

Little Shane’s Visit

Fitting the scuttle seals was not as difficult as I expected. The job was made much easier by following directions: Scuttle Seal Install Rich Chrysler along with those provided by Bill Bolton.

Scuttle seal 1

Scuttle seal rivets 1

scuttle seal screw holes

Scuttle seal rivets 2

I then installed the dash pad, along with the hot air outlet defroster masks, the mirror, tonneau turnbuckles, and the stud for the tonneau cover.

Dash Pad seal 1

Dash Pad seal 2

Once the dash and accompanying hardware was installed I was ready to begin the door installation. I first attached the door check strap assembly to each side. Then I taped all the edges of the wings, sills and doors with painter’s masking tape for protection.

Check Strap Assembly 2

Check Strap Assembly 3

My son John (23 years of age and strong) lifted the doors in place and I ran in the door hinge screws. This job was actually easier and less time intensive than I imagined. Of course, I still need to adjust them for proper fit. I had previously attached all the door interior upholstery, trim and hardware which was much easier than installing it all on the car, but it did make the doors quite heavy.

Next on my list was the installation of the headlight buckets, headlight bulbs, and the chrome lens retaining rim. It wasn’t necessary, but I jacked up the front of the car and temporarily removed the splash shields and the tires to give easier access to the rear of the headlight buckets. I experienced a little difficulty with mounting the trim rim but eventually got it to lock into place. Then I secured the parking/flasher light assemblies to the car with the three small machine screws and nuts, and put the clear lens in place.

Headlight installed 1

Headlight installed with lower wing beading

I thought I would check out the fit of the grill and immediately noticed that the horns were preventing the grill from sliding into place. I did not have the original horns and I am using later replacements (these are deeper). I ended up switching the LH and RH units and placing them inside their mounting bracket and this seemed to give me the space I needed for the grill. At some point I would love to find the proper horns!

Horn installed

Now it was on to the tow hook/driving light bracket from Cape International. I bolted the brackets into place and fit the Lucas 570 SLR- 5” driving lights, attached the wiring and tested the lights to find them working beautifully. I had previously installed the light relay, an indicator light and the wiring so that the lights only come on when the bright beams are used.

Auxiliary Driving light bracket and tow hook

My final work for the week was the installation of the three pieces that comprise the front grille. These were fixed to the car without any issue. The splash panel brackets on either side of the car were fastened to the outside grille mounting brackets.

Grille and Lights installed

Side View with both wings and door

Chapter 83 Week Fifty-Three December 17, 2007

Posted on by

This week begins my second year of restoration assembly. I have some time off in the next two weeks so I am hopeful that at the end of the Christmas holiday I will have my front body components on the car.

While waiting for the carb repair, I decided to start a little work on the hardtop assembly. Most of my hardtop restoration components came from Bill Bolton. The hardtop fabric he supplies is very close to the original. I has previously refurbished the headliner frame and had it along with the front cushion covered by Gerry Smith at Classic Upholstery. I glued the fabric to the lower hardtop aluminum cant rail.

hardtop fabric on rail 2

hardtop fabric on rail 3

Fabric was also glued into the corners of the hardtop where the front mounting “J” hooks are located.

hardtop corner fabric

Then I glued some carpet padding onto the hardtop to provide cushion for the headliner frame rails.

hardtop carpet cushion for headliner rails

My repaired front carb returned from Joe Curto yesterday (December 18). Joe replaced the diaphragm. I installed the carbs last night and pleasantly, no leaks! Now I will leave the hardtop work and return to installing the body.

Front SU carb re-installed

I covered all of the edges of the scuttle that come in contact with the front shroud(bonnet surround) with 3M strip caulk. This will prevent heat, fumes and water from entering the cockpit. To make sure I had adequate build up of the caulk, I used a tip from Jack Brashear. I covered the strip caulk on the scuttle with wax paper, installed the shroud and then pulled it off. Where the strip caulk was not pressed against the the wax paper I added more caulk and repeated the process until I was satisfied that I had enough caulk in place.

Shroud strip caulk 2

Shroud strip caulk 1

Ready for the shroud 2

Securing the front shroud to the superstructure was the next step. I began by installing 3/16” aluminum pop rivets in the rear of the shroud along the dashboard flange (5) and scuttle edges(2 per side).

Shroud rivets

I then installed five countersunk flat head screws through the rear flange of the bonnet opening into the edge of the firewall.

Four bolts, washers, and nuts fasten the frame rails to the shroud at the front of the car. The frame rails should fit “inside” the shroud. Three #10 flat head, countersunk machine screws with washers and nuts fasten the front flange of the bonnet opening to the superstructure.

Two #10 flat head, countersunk machine screws with washers and nuts fasten each of the vertical shroud support brackets to the shroud. On the RH passenger side of the car, one of these screws, along with another, is also used to fasten the bonnet prop rod stay bracket.

Hood prop rod stay bracket

The front shroud was now fastened in place! I then attached the carb access panel and I was in business. The panel measurements are in the image below.

carb access measurements

Carb panel installed

I had a surprise visit from my 9 year old grandson, Tyler. As the photo shows he is getting ready to drive the “Bloody Beast.”

Tyler ready to drive

The two windscreen washer jets were installed on the shroud (would have been much easier to do before the shroud was put in place!) and connected with rubber tubing to the reservoir in the parcel shelf. I had previously installed the wiper motor, crosshead and rack, but I now needed to bring the wheelbox assembly up through the front shroud and secure them in place with the rubber washer, chrome bezel and chrome nut. This was not a pleasant job with all the wiring and underdash components in place, but after some struggling the job was accomplished.

Wipers

Chapter 82 Week Fifty-Two December 10, 2007

Posted on by

I sent my front HD8 carb back to Joe Curto. I suspect a faulty diaphragm causing a leak. When I get it back and on the car then I can finish up the cruise control throttle installation and the front bodywork.

In the meantime I went ahead and installed the rear aluminum cockpit moulding. I used 3M strip caulk to seal each piece to the rear surround lip.

The front-most mounting point for the aluminum moulding was a bit of a problem. After consulting with a number of Healey “authorities,” I concluded that the front mounting point is accomplished with #10-5/8” sheet metal screws on the original car. However, the holes in the shroud had become enlarged over the years and a sheet metal screw would not work. Jack Brashear gave me a tip for installing a machine screw and nut that proved very helpful.

There is VERY LITTLE room to work to install the nut for the front mount. Jack recommended using a Keps nut (has a star washer built in) stuck on a hacksaw blade to maneuver the nut to the fixing hole. I used a little 3M strip caulk to hold the nut on the blade. It worked like a charm and now my moulding trim is mounted tightly to the shroud.

Keps nut for aluminum trim installation

Front installation of aluminum cockpit trim

Chapter 81 Week Fifty-One December 3, 2007

Posted on by

Finishing up the cruise control was accomplished next. I designed a bracket for the throttle connection that permitted locating the throttle cable without having to drill any holes in the vehicle. The cruise control throttle cable bracket is mounted to on the top of the firewall diagonal brace and takes advantage of the two vertical mounting bolts for the pedal box. I painted the bracket red making it virtually undetected by the casual observer.

Cruise control bracket 6

Cruise control bracket 3

Cruise control bracket painted

Cruise control bracket 5

Using what I learned on the installation of the RH rear wing, I attached the LH wing in about half the time. I fixed the turnbuckle to the wing before putting the wing on the superstructure.

Turnbuckle installed

It is a good feeling to have both installed. The Beast is actually beginning to look like a car.

RH Rear Wing 1

LH rear wing 2

LH Rear Wing 1

I had my local auto paint store make two body paint spay cans as well as two small bottles for touch up work. I then spray painted the stow-it tube I had made from fiberglass back in the summer along with a sheet metal top I made with the top of the scotch bottle box fastened to the lid. It will be very unobtrusive, and will provide some nice under shroud storage for parts or tools. I borrowed the idea from Tracy Drummond – thanks Tracy.

Stow it tube painted and with gasket and top

Stow it tube 2

My carpenter finished the transformation of my shoe box model for a console to the real thing in wood. He did a beautiful job. I inserted the wood lid into the underside of the padded arm rest from Heritage and then covered the box in black carpet. Now I have something that almost looks as original, and it also is comfortably  functional! The top is hinged and it has a lower tray to stow small items.

Console 1

Console 3

Console 7

Console Installed

The final job for this week was the installation of the aluminum cockpit moulding on the rear shroud. I had my moulding cleaned, buffed and anodized by Ano-Brite in California. They did a fantastic job. I highly recommend them. I used some 3M strip caulk under the moulding to seal out water from the exterior.

Cockpit trim 1

Cockpit trim 3

Chapter 80 Week Fifty November, 26 2007

Posted on by


I had a little fun today, on the first day of December, 2007! I was able to drive the car, sans most of its bodywork, in the driveway and on our tennis court. Not far, but enough to enjoy the thrill of the progress to this point. I think the grin on my face says it all!

Pushed out of the garage

Almost a shame to cover it up with the body

Missing some body parts

Happy Day!

To the race track

Exhilarating!!

 

 

Chapter 79 Week Forty-Nine November, 19 2007

Posted on by

 


I am now waiting on Jack Harper to get free from his shop duties at Coachworks to come by the house and help me with starting and tuning the engine. While waiting, I took a few moments to check on  sealing the firewall from fumes and heat emitted from the engine bay. I turned off the the lights in the garage and put a shop light in the engine bay and then inspected the firewall for any light coming through the firewall. As expected, I did find a few places, so I used a little 3M body caulk to seal the holes.

Another variance from originality on my project is the “personalized” arm rest. Its standard location makes it virtually useless as a functioning arm rest while driving. I am going to make a wooden box to fit the arm rest pad sourced from Heritage Upholstery and Trim to serve as a storage console and to lift the height of the pad to make it work as an arm rest while driving. I will cover the box with matching black carpet and hinge it at the rear of the pad. To begin my little project, I made a mock-up of the box from a cardboard shoebox. For me, 2 3/4” appeared to be the proper height of the box, with the cushion on top of the box.

Arm Rest Prototype

Jack Harper came over to the house and we readied the engine for starting. First, we connected the cables for the throttle and choke. While the previous injection of oil through the engine should have sufficiently lubricated everything, I still pulled the spark plugs and turned the engine with the starter until the gauge showed oil pressure. I put 5 gallons of fuel in the tank and we turned on the ignition to try out the fuel pump. The carb float chambersfilled and we were then ready to try firing up the Bloody Beast.

We reinstalled the spark plugs, turned on the ignition and hit the starter button. After about 10 seconds we had the engine running! Jack ran the engine up between 2,000 and 2,500 rpms and then we adjusted the carbs to bring the idle down to about 700. After 30 years another Healey is saved and running. It was an exciting moment.

I did have two problems to be fixed. I had taken apart the hot water valve, cleaned it, reassembled and installed it on the engine. It leaked! So I ordered a new one to replace the original. The second problem was my own stupidity! I did not replace the  Toyota gearbox real oil seal and I quickly discovered that I should have as a pool of MT-90 formed under the car. New seal ordered also. Cannot wait to get both pieces, install them, and get her running again!