Daily Archives: July 10, 2024

Custom Brake Switch

Posted on by

Recently produced hydraulic pressure switches for brake light activation are often faulty and/or don’t last long.

Hydraulic Brake Light Switch

We decided to use an electronic pedal activated pressure switch as a complement to the hydraulic switch. We sourced the switch from Moss Motors, part number 542-371.

Lucas-type Brake Light Switch

We have modified the wiring harness to accommodate both switches. Trevor Fawcett, in the U.K., fabricated a simple bracket to hold a Lucas pedal switch and we used that as a model for our own bracket – similar, but not the same.

Trevor’s Brake Switch and Bracket

Trevor’s Brake Switch and Bracket Mock-up

This was our starting pattern (it was slightly modified later), and our bracket after a little bending of a single flat piece of steel in the vice.

Brake Switch Bracket Pattern

Brake Switch Bracket Fabricated

After drilling holes for mounting the bracket to two of the 1/4″ – 28 x 1″ bolts holding the pedal box to the chassis and drilling a 1/2″ hole for the switch we we ready to mount the assembly to the car. Following trial fitting we trimmed a bit here and there, rounded the sharp corners and painted it black.

Pedal Brake Bracket & Switch Mounted to the Pedal Box

Finally, we connected two trial wires to the switch’s spade connectors and tested the sensitivity of the switch with a test light. The results are depicted in the short Bugeye Restoration Video Episode Seventy-three below:

https://vimeo.com/982091053/002655f0fb?share=copy

 

Front Hub Assemblies Installed

Posted on by

We had previously built-up the front hub assemblies including the “A” arms, stub axles, king pins, bearings, hubs, rotors, calipers and etc. This process is covered in “Front Hub Assemblies and Brakes” https://valvechatter.com/?p=13792

The “Front hub Assemblies and Brakes” post also includes a video depicting the process.

“Rebuilt Front Suspension Installed in the Car” https://valvechatter.com/?p=13828 is another post made earlier in the restoration process that is helpful to review before installing the front hub assemblies.

Installing these components can be approached two ways. One can assemble everything on the bench and then mount the entire assembly to the chassis as we did. Alternatively, one can mount the “A” arm and the shock absorber to the chassis and then build-out the assembly on the car. This method is the one explained in the owner’s manual.

Choosing the approach we did certainly made it easier to put the various pieces together, but you end up with a pretty heavy unit that can be a bit of a struggle to mount to the chassis. Resting everything on a floor jack helps, but it is still difficult to get the holes and lower fulcrum pins lined up perfectly. At any rate the job is done.

The two plates below show the various parts that are used to comprise the assemblies. Note that the lower fulcrum pins are inserted from the inside of the chassis cavity with the special washers toward the front and rear of the car. The second plate shows the earlier drum brakes while we are using later front disc brakes.

Front Suspension Components

Front Suspension Components 2

 

Bugeye Restoration Video Episode Seventy-two shows the process of installing the completed front hub assembly to the chassis. https://vimeo.com/981964234/b1aa7a5a24?share=copy

0:00 – Front suspension hub assembly

1:07 – Installing rubber rebound buffers

1:35 – Cleaning paint from chassis mounting area to “A” arms

2:09 – Poly lubricant on fulcrum pins and bushings

2:44 – Moving the hub assembly into position

3:11 – Fulcrum pins and special washers installed

4:26 – Wood spacer blocks installed

4:56 – Upper fulcrum pin locking bolt into shock

5:50 – Coil spring installation

6:30 – Coil spring installation tool

6:54 – Compressing the coil spring

 

The split pin on the upper fulcrum pin was then installed. All bolts and nuts were checked for tightness with the exception of the lower fulcrum pins and nuts to be tightened when the car is on the ground. A little paint touch up on a few scratches completed the process.