Ten Year Renewal Check List

Bloody Beast Ten Year Renewal Plan

 

This is an initial draft of a check list for my ten year renewal project. I would love to have feedback from others on the completeness of the list. Obviously, some of these items will have been tended to rather recently during routine maintenance and they will now just get a quick check. My car is low mileage since its total restoration nine-plus years ago. Consequently, numerous items will not involve the typical wear one might see for this period of time. Instead, the item might need attention for age rather than wear.

Thanks to those readers who have written suggesting items to add to my check list. I appreciate your review! I have updated the list and it is current as of October 3, 2018

 

Bloody Beast Ten Year Renewal Plan

 

Body

RH side curtain vent installation – Unique to my situation

Repair all paint chips with touch up paint

Modify the Cape International rear bumper brackets to move the bumpers closer to the shroud. – Unique to my situation

Clay, Polish, and Wax

Lubricate Bonnet, Door, and Boot hinges and locks

White grease on door locks

White grease on bonnet catch

White grease on boot lock

 

Brakes and Clutch

Flush and refill hydraulic fluid and consider replacement of the master cylinders, bleed system. Outer portion of reservoir feeds the braking system. Inner portion feeds the clutch.

Check condition of all brake lines and rubber hoses and replace if needed

Consider replacing parts of the Cape International rear disc brake conversion with Steve Gerow’s kit. Unique to my situation

Inspect brake pads and renew if needed.

Check tightness of the slave cylinder fasteners.

Grease handbrake cable and compensator

 

Cooling

Replace radiator upper and lower hoses

Replace the fan belt

Check condition of the radiator cap

Flush coolant and replace with new coolant.

 

Electrical System

Replace alternator – Unique to my situation

Check all electrical connection points

Check condition of the battery and clean posts if needed.

Check tightness of fasteners securing the ground strap in the boot.

Add a back-up light from the gearbox

Replace the incandescent courtesy lamps with LED lights

 

Engine

Check tightness of Crankshaft starter nut and harmonic balancer

Adjust valve clearances

Oil and oil filter (K&N HP-2009) change – replace copper crush washer at drain plug

Check engine for leaks and repair where possible. Check the oil sump bolts.

Replace gaskets/seals for generator mounting plate and tappet covers.

Check tightness of all oil sump mounting bolts.

Replace rocker cover seal.

Replace the rocker cover “T” breather pipe with Cape International “U” pipe to take breather hoses to a Mishimoto oil catch can.- Unique to my situation

Check condition of engine mounts and bolt tightness.

Visually inspect core plugs for any seepage

 

Exhaust

Inspect system for any leaks and repair if needed

Check for tightness of fasteners

 

Fuel

Replace fuel filter – Malassi Filter King and Holley Gauge

Replace rubber fuel hose with ethanol resistant hose.

Check tightness of Carb fittings. Clean and polish carbs check damper oil level.

Change ITG air filter to Burlen Ram Pipes. – Unique to my situation

Adjust carbs as needed. See Steve Byers instructions.

Consider a reworking of the fuel delivery hose system from pipe to carbs. Unique to my situation.

Add a ground connection wire from the fuel sender unit to the frame.

Check fuel sender/gasket for any fuel leakage.

Lubricate carb linkages with light oil

 

Front suspension

Check condition of rubber boots on ball joints and other bushings.

Check the tightness of all shock absorber mounting bolts.

Check Oil in the shock absorbers.

Check the tightness of the nuts/bolts under the spring pans.

Check the working condition of all grease zerks and grease them.

Inspect the front bearings. Repack or replace. Set end-float to spec.

Inspect the splines on the hubs and the wheels. Make sure all hub nuts are tight.

Check for wear in the king pin by testing to see if there is movement when grabbing the tire at the bottom and trying to move it in and out.

 

Gearbox & Propshaft

Check all mounting fasteners for tightness.

Drain gearbox oil and replace with a little less than 3 quarts of Red Line MT-90 synthetic gear oil.

Check condition of U-joints (?)

 

Heater

Inspect rubber heater hoses and replace if needed.

Consider replacement of the heater water valve to ensure it is not clogged.

 

Ignition

Inspect ignition system wiring and connection points

Inspect spark plugs and replace with new NGK BP6ES plugs

Check engine timing

 

Interior

Replace bristleflex door seals

Treat leather surfaces with conditioner.

Check oil seal on the back of the tachometer to see if there are any drips.

 

Lights

Check all bulbs and flashers for correct operation

Check operation of all dash lights

 

Rear Axle & Suspension

Refresh Axle Differential Gear Oil

Check fasteners for U-bolts, shock absorbers

Check the working condition of all grease zerks and grease them

Check the breather on the the axle casing

Check rear bearings for smooth turning and seals for leaks

Check oil in the shock absorbers

 

Steering

Check fill levels of the steering idler and steering box and add Penrite Steering Oil.

Check tightness of all fasteners and rubber ball joint boots.

 

Tires

Inspect for age and wear. Replace if needed.

Check inflation pressures and adjust if needed.

 

Wheels

Inspect all wheels for loose spokes. Repair if needed.

 

Windshield & Windshield Washer

Inspect and refresh fluid in reservoir

Replace wiper blades

 

3 thoughts on “Ten Year Renewal Check List

  1. as usual, very comprehensive.
    Vacuum carpet and check fuel sender to be sure it’s not leaking around seal.
    Check under battery for acid presence.clean terminal connections and check ground strap to frame.

  2. 1. Remove propshaft from back of Overdrive and check condition of castellated nut and split pin, tighten if necessary, and check for leaks from oil seal while you are there.
    2. Check tightness of the starting nut and condition of harmonic balancer while you are at it.
    Both have come loose on me this year after 10-12 years on the road.

    • Thanks, Ross. In my case, I am using a Supra gearbox, so no overdrive to check. I will add the harmonic balancer and starting nut to my list.
      Lin

Comments are closed.